Lihat Juga

• The research objectives are to evaluate physical and mechanical properties of OSB based on strand orientations made from akasia wood (Acacia mangium Wild) and afrika wood (Maesopsis eminii Engl). Akasia and afrika wood are used for OSB strand material with phenol formaldehyde (PF) as adhesives and addition of paraffin. OSB made in this research consists of three plies whereas are differed into eight strand orientations. Hot press was carried out at 160oC and pressure 25 kg/cm2 for 15 minutes. Determination of OSB physical and mechanical properties referred to JIS A 5908-2003. Result showed that strand orientations have not affected to OSB physical properties except for linear swelling 24 h, but it significantly influences all mechanical properties of OSB. Wood species has an effect on mechanical properties of OSB in the dry test, wet MOE lengthwise test and OSB physical properties, particularly to OSB density and water absorbing capability at 2 h and 24 h. All of OSB physical properties are meet JIS A 5908-2003 standard, but not all of the mechanical properties such as dry MOE lengthwise, dry MOE and MOR widthwise. The best physical and mechanical properties is presented by OSB made from akasia wood in strand orientation F (core layer is orientated and surface layers are in random, R°/0°/R°), G (core layer is orientated 45° and surface layers are in random, R°/45°/R°), B (surface strand direction is upright to core strand direction, 0°/90o/0°), and C (core layer is in random, surface layers are orientated, 0°/R/0°) whereas all parameters meet JIS A 5908-2003 standard. In comparation with strand orientation B that is frequent used in industry, strand orientation F and G are proficient to raise the modulus elasticity value (MOE) and strength (MOR) as much as 167.8-231.7% and 89.7-109.9%, respectively; especially in widthwise board application. Furthermore, strand orientation F and G are more flexible as structural components. Keywords: Oriented strand board, strand orientation, phenol formaldehyde
  oleh: ., NURHAIDA, et al.
  Terbitan: (2012)
• The objectives of this research were to determine and to compare the physical and mechanical properties of OSB made of strands from three small diameter fast growing species, namely Akasia (Acacia mangium Willd.), Ekaliptus (Eucalyptus sp.), and Gmelina (Gmelina arborea Roxb.). There were 3 models of OSB produced which bonded by 2 types of adhesive, namely Phenol Formaldehyda (PF) powder type, isocyanate (IC), and the face and back layers bonded by powder PF and the core layer bonded by IC. OSB was made of three plies, with 9 mm target thickness and ratio of strands weight in face : core : back was 1:1:1. Mat forming methods in face was lengthwise and the core was widthwise. Level of adhesive 7% based on oven dry strands weight, pressed at 25 kg/cm2 for 15 minutes at 160 °C. Japanese Industrial Standard (JIS) A 5908-2003 for particle board 24-10 type was used as standard. Results of this research showed generally physical properties consist of density, moisture content, and thickness swelling fulfilled JIS A 5908-2003 standard. Unfortunatelly, the dimensional stability should be improved, the range 24 hours water absorption was about 22.35–44.63%. For mechanical properties, which consist of internal bonding, modulus of rupture (MOR) and modulus of elasticity (MOE) which be evaluated in dry condition both lengthwise and widthwise generally fulfilled JIS A 5908-2003 standard. However, there were values of MOR and MOE which be evaluated in wet condition both of lengthwise and widthwise did not fulfill JIS A 5908-2003 standard. The best performance of OSB was which bonded by IC for all the wood species. Using PF powder at the face and back layers and IC in the core layer of OSB generally increased their physical properties (dimensional stability) but decreased their mechanical properties. Keywords : Physical and mechanical properties, OSB, small diameter fast growing species, adhesive
  oleh: NURYAWAN, Arif, et al.
  Terbitan: (2012)
• The objective of this research is to evaluate the characteristic of composite board made from coconut fibre, recycled polypropylene (RPP), and bamboo matting layers. The board samples target density was 0,70 g/cm3. The board construction type was core type composite board (three layers). Coconut fiber and RPP were used as core, and bamboo matting was used as face and back layers. RPP was used 50% based on coconut fiber oven dry weight. The bamboo sheet wide is 1 cm and 2 cm, with and without bark. The bamboo matting layers were used in slope (45 ̊) and perpendicular (0/90 ̊) orientation to length of the board. The research results showed that utilization of bamboo matting layers increase the mechanical properties of board. All of composite board made from coir, RPP, and bamboo matting layers fulfill the JIS A 5908 standard in density, thickness swelling after 24 hours of water immersions, and screw holding power. Only composite boards with bamboo matting layers with bark, sheet wide 1 cm, and perpendicular orientation to length of the board fulfill JIS A 5908 1994 standard for veneered particleboard in MOE. However, application of bamboo matting layers without bark is adviced better because more efficient in the raw material using. Keywords: Composites board, coconut fiber, recycled polyprophylene, bamboo matting layers
  oleh: SETYAWATI, Dina, et al.
  Terbitan: (2012)
• Physical and Mechanical Properties of OSB Made from Bamboo
  oleh: Saad, Sahriyanti, et al.
  Terbitan: (2011)
• The purpose of this study was to analyze the phisycal and mechanical properties of binderless particleboard using bamboo as raw materials. Andong bamboo (Gigantochloa pseudoarundinaceae) used in this study was taken from Bogor area. Bamboo was converted using hammer mill and air dried subsequently. The particle zise was passed of the 20 mesh screener. Three types pretreatment were used to prepare the particle, namely : 1) water boiling for 30 and 60 minutes, 2) oxydation using hydrogen peroxyde, and 3) combination of water boiling for 30 minutes and oxydation using hydrogen proxide. As a control, conventional particleboards using 10 % melamine formaldehyde (MF) resin based on dry particle weight was produced. The particle which has pretreated then utilized to produce binderless particleboard with board density of 0.75 g/cm3. The pressing conditions were 180 oC in temperature, 25 kgf/cm2 in pressure for 20 minutes. The board characteristics were tested according to JIS A 5908 2003. The results indicated that particleboard made from particle with oxydation pretreatment performed superior characteristics compared to those of particleboard made from particle only with water boiling pretreatment. Dimensional stability and modulus of elasticity of board with oxydation pretreatment were excellent. Its was superior compared to that of conventional particleboard using melamine formaldehyde as adhesive. Keywords : Bamboo, Binderless Particleboard, Oxydation, Hydrogen Peroxyde
  oleh: ., SUHASMAN, et al.
  Terbitan: (2012)